Mac + Uno + avrdude: stk500_recv (): dasturchi javob bermayapti

Arduino-ga .hex faylini yuklashga harakat qilaman. IDE orqali kodni o'rnatish bilan bog'liq muammolar yo'q (masalan, miltillovchi misol yoki boshqa). Port va taxta to'g'ri.

Yuklab olishga harakat qilsam muammo paydo bo'ladi

avrdude -pm328p -carduino -P/dev/tty.usbmodemfd121 -b57600 -D -Uflash:w:grbl_v0_8c_atmega328p_16mhz_9600.hex -v -v -v -v

avrdude: Version 6.1, compiled on Mar 23 2014 at 04:42:55
     Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
     Copyright (c) 2007-2014 Joerg Wunsch

     System wide configuration file is "/usr/local/Cellar/avrdude/6.1/etc/avrdude.conf"
     User configuration file is "/Users/Mikhail/.avrduderc"
     User configuration file does not exist or is not a regular file, skipping

     Using Port                    : /dev/tty.usbmodemfd121
     Using Programmer              : arduino
     Overriding Baud Rate          : 57600
avrdude: Send: 0 [30]   [20] 
avrdude: Send: 0 [30]   [20] 
avrdude: Send: 0 [30]   [20] 
avrdude: ser_recv(): programmer is not responding
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x00

Men nima qildim?

  • I have 4 Uno's at the table (original + free versions), the same issue.
  • I have installed newest drivers from here, tried with and without them.
  • tried with avrdude which comes with Arduino IDE (1.0.5 and nightly builds) and newest avrdude v.6.1 brew install avrdude
  • different baud rates down to 9600
  • tried to press reset after bytes are sent like suggested here
6
Tahririyatga o'z vaqtida tiklash uchun [hoi pollioning javobini] bu erda [1] men uchun ishlagan. [1]: stackoverflow.com/questions/19765037/…
qo'shib qo'ydi muallif Walrus the Cat, manba

12 javoblar

Men uchun nima aniq bo'lgan:

  • USB kabelini Arduino dan ajratib oling
  • Dasturingizni yuklab olishga harakat qiling
  • Bu muvaffaqiyatsizlikka uchraydi va Arduino dasturi qaysi USB portini ishlatishini so'raydi.
  • Buni ikki marta qildim
  • Keyin USB kabelini Arduinoga ulang
  • Dasturingizni yuklashingiz ... muvaffaqiyat!

Eslatma: Mixail tomonidan qayd etilgan haydovchilarni o'rnatishdan oldin.

O'rnatish: Mac OS 10.9.5, Arduino.app 1.0.6, Arduino Duemilanove

4
qo'shib qo'ydi
Bugungi kunda MacOS Sierra 10.12.4 da Arduino App 1.8.2 va Arduino Uno bilan ishladi.
qo'shib qo'ydi muallif Chris Cartland, manba

Men uchun nima aniq bo'lgan:

  • USB kabelini Arduino dan ajratib oling
  • Dasturingizni yuklab olishga harakat qiling
  • Bu muvaffaqiyatsizlikka uchraydi va Arduino dasturi qaysi USB portini ishlatishini so'raydi.
  • Buni ikki marta qildim
  • Keyin USB kabelini Arduinoga ulang
  • Dasturingizni yuklashingiz ... muvaffaqiyat!

Eslatma: Mixail tomonidan qayd etilgan haydovchilarni o'rnatishdan oldin.

O'rnatish: Mac OS 10.9.5, Arduino.app 1.0.6, Arduino Duemilanove

4
qo'shib qo'ydi
Bugungi kunda MacOS Sierra 10.12.4 da Arduino App 1.8.2 va Arduino Uno bilan ishladi.
qo'shib qo'ydi muallif Chris Cartland, manba

Men uchun nima aniq bo'lgan:

  • USB kabelini Arduino dan ajratib oling
  • Dasturingizni yuklab olishga harakat qiling
  • Bu muvaffaqiyatsizlikka uchraydi va Arduino dasturi qaysi USB portini ishlatishini so'raydi.
  • Buni ikki marta qildim
  • Keyin USB kabelini Arduinoga ulang
  • Dasturingizni yuklashingiz ... muvaffaqiyat!

Eslatma: Mixail tomonidan qayd etilgan haydovchilarni o'rnatishdan oldin.

O'rnatish: Mac OS 10.9.5, Arduino.app 1.0.6, Arduino Duemilanove

4
qo'shib qo'ydi
Bugungi kunda MacOS Sierra 10.12.4 da Arduino App 1.8.2 va Arduino Uno bilan ishladi.
qo'shib qo'ydi muallif Chris Cartland, manba

Hex Uploader bilan muvaffaqiyatli hal qilindi.

Mac OS uchun Arduino-ga .hex fayllarini o'chirish uchun yaratilgan.

Boshqa operatsion tizimlar uchun imkoniyatlar quyidagicha tavsiflanadi: grbl hujjatlari .

0
qo'shib qo'ydi
Bu men uchun ish bermadi, men xato qildim.
qo'shib qo'ydi muallif Agent Zebra, manba

Kecha kechqurun My Arduino Uno bilan bir xil muammo bor edi. Boshimni devorga urganimdan so'ng, Arduino IDE'ni 1.6.0 ga o'zgartirdim. Buni faqat Mac OS X-da qildim, shunchaki Arduino bosh sahifasidan 1.6.0-ni yuklab olish.

Buni o'rnatganingizdan keyin mening ishimdagi to'g'ri taxtani tanlash kabi:/dev/tty/usbmodem ____ (Arduino Uno)

Xatolik shifo topdi va dasturlarni tiklashni istamasdan yana bir marta yuklashni xohlayman, ya'ni dasturni tiklash tugmachasini 5 soniya ushlab turgandan so'ng, ya'ni bir soniyadan keyin.

Xo'sh, bu men uchun ishlagan, boshqalar uchun ishlaydigan umid!

0
qo'shib qo'ydi

I had same problem with Ardunio Leonardo board. I notice that I forgot to set my board version from IDE. After selecting correct board (Tools --> Board --> Ardunio Leonardo) problem solved.

0
qo'shib qo'ydi

I had same problem with Ardunio Leonardo board. I notice that I forgot to set my board version from IDE. After selecting correct board (Tools --> Board --> Ardunio Leonardo) problem solved.

0
qo'shib qo'ydi

Men faqat Amazondan arduinomonek nano-board sotib oldim va bu aniq muammoga yugurdim. Arduino dasturiy ta'minot versiyasi 1.0.5 va Mac OSX 10.9.4 versiyasini ishlayapman.

Ko'p turli xil takliflarni sinab ko'rdim (xuddi siz yuklayotganingizda resetni saqlash kabi) va ishonchli tarzda ishlamagan. Barcha hujjatlarda Mac uchun yangilangan USB haydovchilarga ehtiyoj borligini bildirgan bo'lsam, faqatgina yangilangan drayverlarni yuklab qo'ydim: http://www.ftdichip.com/Drivers/VCP.htm (2.2.18)

FTDI ..._ 10_4 _ faylini yuklab olish va ishga tushirishdan so'ng. O'rnatilgandan so'ng, arduino IDE ga qaytib, sketchni o'rnatdi ... u mukammal ishladi!

0
qo'shib qo'ydi

Men faqat Amazondan arduinomonek nano-board sotib oldim va bu aniq muammoga yugurdim. Arduino dasturiy ta'minot versiyasi 1.0.5 va Mac OSX 10.9.4 versiyasini ishlayapman.

Ko'p turli xil takliflarni sinab ko'rdim (xuddi siz yuklayotganingizda resetni saqlash kabi) va ishonchli tarzda ishlamagan. Barcha hujjatlarda Mac uchun yangilangan USB haydovchilarga ehtiyoj borligini bildirgan bo'lsam, faqatgina yangilangan drayverlarni yuklab qo'ydim: http://www.ftdichip.com/Drivers/VCP.htm (2.2.18)

FTDI ..._ 10_4 _ faylini yuklab olish va ishga tushirishdan so'ng. O'rnatilgandan so'ng, arduino IDE ga qaytib, sketchni o'rnatdi ... u mukammal ishladi!

0
qo'shib qo'ydi

Had the same problem. But my fixed it by going to Tools->Serial Port, then selecting tty.ADR6300-SerialPort

0
qo'shib qo'ydi

Had the same problem. But my fixed it by going to Tools->Serial Port, then selecting tty.ADR6300-SerialPort

0
qo'shib qo'ydi

Had the same problem. But my fixed it by going to Tools->Serial Port, then selecting tty.ADR6300-SerialPort

0
qo'shib qo'ydi